WELCOME TO WOOX SUPPORT
We get it, sometimes a little guidance is needed. We're here to help.
Still stuck? Drop us a note.
Have a question about shipping, returns or want to know more about our shopping policies? Click here and soak in the knowledge.
ASSEMBLY
STEP 1. With the rifle attached to the original stock, turn the rifle upside-down in the rest so the underside of the rifle is facing up.
STEP 2. With the bottom of the rifle turned up, remove both forward and rear action retention screws (located at forward and rear of the trigger guard). If there is a base plate, remove it now. The original rifle stock should lift free of the rifle.
STEP 3. Place the Furiosa rifle chassis on the barrel and action and replace the base plate. Then replace the forward and rear action retention screws and torque them to the manufacturer’s specifications.
STEP 4. Make sure your WOOX rifle stock is properly seated to the rifle.
STEP 5. Your rifle should be properly attached to your new WOOX stock. Read all safety materials before operating.your new WOOX stock. Read all safety materials before operating.
CLEANING AND CARE
1. Remove the rifle from the stock.
2. Dampen a cleaning cloth with WOOX Cleaner. Clean front to back.
3. To clean the front stock and M-LOK® rails, first remove the 5mm Allen screw.
4. Remove all nine (9) M-LOK® screws. Clean any dirt, dust, or debris.
5. Reassemble in reverse order of disassembly.
6. Detach rear stock from monobloc housing and clean them both.
7. Remove cheek rest and butt pad and clean with a brush and rag.
8. Remove wooden grips from rear stock skeleton. Clean grips and stock with a brush and rag. Reassemble in reverse order of disassembly.
9. Reattach the cheek rest and butt pad to the rear stock, then reattach the rear stock to the monobloc body. Wipe away remaining cleaner solvent.
10. Reassemble the rifle to the stock.
11. Wipe down the rifle and stock with a light coat of the rifle manufacturer’s recommended gun oil.
NOTE: Use only a vinyl brush to clean any dirt, dust, or debris from the rear stock butt pad or cheek rest housing holes. DO NOT insert metal objects into the rear stock butt pad or cheek rest housing holes.
ASSEMBLY
STEP 1. With the rifle attached to the original stock, turn the rifle upside-down in the rifle rest so the floorplate is facing up. Release the magazine button.
STEP 2. With the bottom of the rifle turned up, remove both forward and rear action retention screws (located at forward and rear of the trigger guard). If there is a base plate, remove it now. The original rifle stock should lift free of the rifle.
STEP 3. Place the WOOX Exactus rifle stock on the barrel and action and replace the base plate. Replace the forward and rear action retention screws and torque them to the manufacturer’s specifications.
STEP 4.Make sure the magazine-well is seated properly on the rifle and close the floor plate.
STEP 5.Your rifle should be properly attached to your new WOOX stock. Read all safety materials before operating.
CLEANING AND CARE
1. Remove the rifle from the stock.
2. Dampen a cleaning cloth with WOOX Cleaner. Clean front to back.
3. To clean the front stock and M-LOK® rails, first remove the 5mm Allen screw.
4. Remove all nine (9) M-LOK® screws. Clean any dirt, dust, or debris.
5. Reassemble in reverse order of disassembly.6. Detach rear stock from monobloc housing and clean them both.
7. Remove cheek rest and butt pad and clean with a brush and rag.8. Remove wooden grips from rear stock skeleton. Clean grips and stock with a brush and rag. Reassemble in reverse order of disassembly.
9. Reattach the cheek rest and butt pad to the rear stock, then reattach the rear stock to the monobloc body. Wipe away remaining cleaner solvent.
10. Reassemble the rifle to the stock.
11. Wipe down the rifle and stock with a light coat of the rifle manufacturer’s recommended gun oil.
NOTE: Use only a vinyl brush to clean any dirt, dust, or debris from the rear stock butt pad or cheek rest housing holes. DO NOT insert metal objects into the rear stock butt pad or cheek rest housing holes.
ASSEMBLY
STEP 1. With the rifle attached to the original stock, turn the rifle upside-down in the rifle rest so the floorplate is facing up. Release the magazine button.
STEP 2. With the bottom of the rifle turned up, remove both forward and rear action retention screws (located at forward and rear of the trigger guard). If there is a base plate, remove it now. The original rifle stock should lift free of the rifle.
STEP 3. Place the WOOX Wild Man rifle stock on the barrel and action and replace the base plate. Replace the forward and rear action retention screws and torque them to the manufacturer’s specifications.
STEP 4.Make sure the magazine-well is seated properly on the rifle and close the floor plate.
STEP 5.Your rifle should be properly attached to your new WOOX stock. Read all safety materials before operating.
CLEANING AND CARE
1. Remove the rifle from the stock.
2. Dampen a cleaning cloth with WOOX Cleaner. Clean front to back.
3. To clean the front stock assembly, first remove the T25 Torx bit. Also, remove both sling mount screws. Clean all necessary areas.
4. Reassemble in reverse order of disassembly.
5. Clean mono bloc housing. Wipe away remaining cleaner.
6. Wipe down the rifle and stock with a light coat of the rifle manufacturer’s recommended gun oil.
NOTE: Use only a vinyl brush to clean any dirt, dust, or debris from the rear stock butt pad or cheek rest housing holes. DO NOT insert metal objects into the rear stock butt pad or cheek rest housing holes.
ASSEMBLY
STEP 1. With the rifle attached to the original stock, turn the rifle upside-down in the rifle rest so the floorplate is facing up. Release the magazine button.
STEP 2. With the bottom of the rifle turned up, remove both forward and rear action retention screws (located at forward and rear of the trigger guard). If there is a base plate, remove it now. The original rifle stock should lift free of the rifle.
STEP 3. Place the WOOX Cobra rifle stock on the barrel and action and replace the base plate. Replace the forward and rear action retention screws and torque them to the manufacturer’s specifications.
STEP 4. Make sure the magazine-well is seated properly on the rifle and close the floor plate.
STEP 5. Your rifle should be properly attached to your new WOOX stock. Read all safety materials before operating.
CLEANING AND CARE
1. Remove the rifle from the stock.
2. Dampen a cleaning cloth with WOOX Cleaner. Clean front to back.
3. To clean the front stock assembly, first remove the T25 Torx bit. Also, remove both sling mount screws. Clean all necessary areas.
4. Reassemble in reverse order of disassembly.
5. Clean mono bloc housing. Wipe away remaining cleaner.
6. Wipe down the rifle and stock with a light coat of the rifle manufacturer’s recommended gun oil.
NOTE: Use only a vinyl brush to clean any dirt, dust, or debris from the rear stock butt pad or cheek rest housing holes. DO NOT insert metal objects into the rear stock butt pad or cheek rest housing holes.
CLEANING AND CARE
1. Dampen a cleaning cloth with WOOX Box Degreaser and wipe down the knob and head handle of the axe.
2. Wipe down with a clean, dry rag.
CLEANING AND CARE
To clean the ax head:
• To clean your axe first make sure that the head is thoroughly dry. Use a WOOX bamboo cloth or a towel to remove excess water or moisture from the axe blade.
• If there is stubborn dirt or wood sap on the head, scrape it off with a wire brush. Large pieces can also be scraped off gently with a knife.
• If necessary, remove any remaining grime on the axe head with a WOOX degreaser or solvent or paint thinner.
• If you spot rust, scratch it off using sandpaper or steel wool and clean any particles with an oiled cloth or paper towel.
• Once the axe head is clean - you’re ready to sharpen it.
For the handle:
• Clean any dirt and debris with WOOX bamboo cloth or a clean dry cloth.
• Once clean, rub a small amount of boiled linseed oil to help preserve the wood.
How to Sharpen
Most axes don’t need to be razor sharp.
With axes, your goal should be to get a clean, workman-like edge.
• Axe sharpening works best when the axe is locked in place. This way, both your hands are free to use the file for sharpening. turn the axe or blade flat so that it’s parallel to the ground.
• In most circumstances, lubricating your stone is going to be a the right choice.
• Forte has a 15° scandi edge. In general, you want to aim for keeping the angle as similar as possible to what the edge is currently.
• Begin by spritzing the surface to keep a puddle of water on top. This helps lubricate the sharpening stone and move the metal and stone particles away as you sharpen.
• Start at the top edge of the blade, apply pressure downward while moving the blade back and forth over the top of the stone, with a slight rotation. A great way to make sure you sharpen the entire bit is to move in small circles and not long strokes.
• Sharpen each section in overlapping phases, applying an equal number of back-and-forth round sets to each section.
• Flip the blade over and repeat the process to the other edge of the Axe.
• To further hone the blade, flip the stone over, and repeat the process on both sides of the blade.
• When done sharpening, rinse the surface of the stone again with water let air-dry.
CLEANING AND CARE
1. Dampen a cleaning cloth with WOOX cleaning kit degreaser. Wipe down the knife removing any dust, dirt or debris from the blade and handle.
2. Inspect for any damage or wear and tear. If anything is damaged please contact WOOX customer service.
3. Remove both screws holding the handles to the knife. Dampen a rag with WOOX Cleaner. Clean the handles and the body of the knife removing any dust, dirt or debris.
4. Reattach handles in reverse of disassembly.
5. Wipe the knife of excess cleaner with a clean dry rag.
CLEANING AND CARE
1. Dampen a cleaning cloth with WOOX cleaning kit degreaser. Wipe down the knife removing any dust, dirt or debris from the blade and handle.
2. Inspect for any damage or wear and tear. If anything is damaged please contact WOOX customer service.
3. Remove both screws holding the handles to the knife. Dampen a rag with WOOX Cleaner. Clean the handles and the body of the knife removing any dust, dirt or debris.
4. Reattach handles in reverse of disassembly.
5. Wipe the knife of excess cleaner with a clean dry rag.
CLEANING AND CARE
1. Dampen a cleaning cloth with WOOX cleaning kit degreaser. Wipe down the knife removing any dust, dirt or debris from the blade and handle.
2. Inspect for any damage or wear and tear. If anything is damaged please contact WOOX customer service.
3. Remove both screws holding the handles to the knife. Dampen a rag with WOOX Cleaner. Clean the handles and the body of the knife removing any dust, dirt or debris.
4. Reattach handles in reverse of disassembly.
5. Wipe the knife of excess cleaner with a clean dry rag.
CLEANING AND CARE
1. Dampen a cleaning cloth with WOOX cleaning kit degreaser. Wipe down the knife removing any dust, dirt or debris from the blade and handle.
2. Inspect for any damage or wear and tear. If anything is damaged please contact WOOX customer service.
3. Remove both screws holding the handles to the knife. Dampen a rag with WOOX Cleaner. Clean the handles and the body of the knife removing any dust, dirt or debris.
4. Reattach handles in reverse of disassembly.
5. Wipe the knife of excess cleaner with a clean dry rag.
Picking the right action length will ensure your new WOOX chassis fits your firearm. Confirm the action length with the handy table below - simply look for the action that corresponds with your caliber. This list is not exhaustive so if you don't see your caliber, ask your firearm manufacturer.
17 Remington
20 PPC
204 Ruger
22 Hornet
22 PPC
22-250 Remington
220 Swift
222 Remington
222 Remington Mag
223 Remington
224 Weatherby Mag
243 Winchester
250 Savage
260 Remington
270 Winchester Short Mag
30 M1 Carbine
30-30 Winchester
300 WSM
308 Winchester
350 Legend
32 Winchester Special
325 WSM
338 Federal
35 Remington
44-40 Winchester
450 Bushmaster
6mm PPC
6mm Remington
6.5 Creedmoor
6.8 Remington SPC
7mm-08
7mm Remington Short Action Ultra Mag
240 Weatherby Mag
264 Winchester Mag
270 Winchester
280 Remington
30-06 Springfield
300 Winchester Mag
338 Lapua
338 Winchester Mag
35 Whelen
350 Remington Mag
45-70 Government
7mm Remington Mag
7mm Remington Ultra Mag
Be sure to familiarize yourself with the WOOX 100 Years of Service program. It details what we can do and what fees may apply. Learn more.
If you ordered directly from WOOX, you may use the online returns center. Get started.
If you did not order directly from us, you may print this email thread and place it in the box with your contact information and ship to:
WOOX Att: Service
1269 19th St Lane NW
Hickory, NC 28601
Engraving adds two (2) weeks to the order processing time. If an order includes expedited shipping, that rush time will be honored when the item ships; we are not able to rush engraving. For example, if you order an engraved knife with 2-day air shipping, it will be two weeks before it ships, at which time it will be sent 2-day air.
YES! The Gladiatore Fore End (Jan 2023 model) is designed only for a 6 1/2” tube. Midway USA has the parts you need to convert your 7 1/2” tube to the shorter length:
Slide Tube Assembly
https://www.midwayusa.com/product/1005522153
Action Tube Nut*
https://www.midwayusa.com/product/1005514790
*optional - you can use your existing nut
The Gladiatore Fore End fits 12-gauge and 20-gauge tubes. It does NOT fit .410-gauge.
No, the Gladiatore Fore End does not work with a heat shield installed. The lower edge of the heat shield is not level, it ramps downward moving towards the muzzle. Because of this shape, the fore end quickly comes into contact and prevents cycling of the action.
Bottom metals enable a rifle to accept and hold a magazine and provide a trigger guard.
WOOX does not include bottom metals with any chassis and if needed, must be purchased separately.
WOOX offers bottom metals for our Remington 700 (and clones) chassis. These bottom metals are produced by Hawkins Precision, a leader in bottom metals manufacturing.
You're ready to buy a bottom metal from WOOX, but unsure about the options. This should help!
WOOX bottom metals by Hawkins Precision are *only* for Remington 700 platforms (and clones). If you're buying a chassis for another platform, consult your firearm manufacturer about your options. In most cases one is not needed.
The bottom metal action length should match your chassis length choice. EXAMPLE: a Furiosa Rem700 SA has one bottom metal option, the SA DBM (Short Action chassis + Short Action bottom metal). For most Rem700 LA users (Long Action), the LA DBM (Win Mag 3.725") will suffice.
SA DBM - Short Action Detachable Box Magazine. Made for use with AICS magazines.
LA DBM (Win Mag 3.725") - Long Action Detachable Box Magazine. Made for long action magnum and standard calibers with with AICS magazines.
LA DBM (CIP -338 Lapua) - Long Action Detachable Box Magazine. Made for use with Accuracy International magazines with an internal case length of 3.750".
LA DBM (CIP+ -338 Lapua) - Long Action Detachable Box Magazine. Made for use with Accurate magazines with an overall length of 3.850".
If it's a short action, it's set up for the Savage Apex. You'll need the Apex front action screw from Savage ($2 part) and a self-retained magazine in your caliber ($40, also from Savage).
If it's long action, it should take the standard manufacturer bottom metal.
The short answer: nope. If it's not listed in the compatibility chart on the product page, that chassis & stock won't fit.
But wait, there's an exception.
Remington 700 clones. The Rem 700 is one of the most popular platforms and dozens of makers base their rifle concepts on this basic design. WE DON'T KNOW THEM ALL, so the first thing to do is to contact your rifle manufacturer and simply ask, "Is this rifle based on the Remington 700?" If they say yes, you're in business and can drop it into a WOOX.
"DBM" = Detachable Box Magazine
Short Action DBM: The short action M5 DBM is made for use with AICS magazines, but will work with AW magazines if your action is cut accordingly.
Long Action DBM: These feature the same features as our short action bottom metals. They are made for long action magnum and standard calibers with AICS magazines. (300 Win Mag, 7 Rem Mag, 30-06, 280AI etc.)
338 CIP Length Notes: 338 CIP bottom metal is designed to use with AICS magazines with an internal case overall length of 3.750”. For use with long action stock inlets.
338 CIP+ Length Notes: Designed for use with Accurate Magazines with a magazine overall length of 3.850”. (.338 Lapua Mag. SSSF Magazine or Accurate 300 RUM magazine) For use with long action stock inlets. These will also work with 3.850″ MDT Magazines. Please note this is the outside dimension of the magazine. Internal COAL is 3.760″ for MDT / 3.750″ for Accurate.
WOOX products are integral to getting the very most from your time outdoors and to ensure they are always there when you need them, we proudly offer 100 Years of Support Service.
• 100 Years of FREE blade sharpening
• 100 Years of FREE chassis maintenance
• 100 Years of FREE technical consultation and assistance
Learn more about what you can expect from WOOX or start your service return below.